Hello !
Northern Virginia Jeepers Association
December 13, 2018, 11:04:48 PM

Pages: [1] Go Down
  Print  
Author Topic: Older TJ Half Doors project  (Read 483 times)
0 Members and 1 Guest are viewing this topic.
packinnova
Offline
Forum User
Posts: 164
« on: July 23, 2018, 10:24:45 AM »

It's been a while since I posted here.  My house reno has been a disaster and taken most of my spare time.  Something reminded me of this project this past weekend.  I couldn't remember if I posted this in here, but I don't see it searching so what the heck.

In short, the old half doors on my spamcan were a mess.  The bottom of the frame had completely rusted out and you could literally stick your hand outside through the bottom from the inside of the Jeep. 

I looked online and new halfdoor frames were like $90... A new project says I!  I'm not the best welder around, but this isn't something that's structural given what I'm repairing so out comes the welding cart.  I had some old sheet steel that was left over from a parts crate and it looked to be about the right thickness. Grab a Wrench!

I think it turned out halfway decent.  Point being you don't have to be a pro for simple fixes and you don't have to spend $100 on replacements either if you have a few tools or like in my case you live at HBF! Wink

Speaking of HBF...  This was done with ALL HBF tools...including the cheapo flux core welder.


Here's what I started with:



Skin stripped off passenger side:



Driver side almost repaired:





PAINTED:




Reskinned and mounted for a nice tight fit again



WWW Logged

'97 Franken-TJ
6" lift and 35's
My Jeep Life Tees and Hoodies:
https://rdbl.co/2mDSQmV
karlmagnum
Offline
Forum User
Posts: 41
« Reply #1 on: November 14, 2018, 02:22:41 AM »

Nice work! It has a snug fit.

Logged
Gr8Dain
Offline
BOD
*
Posts: 11355
I HATE RUST!!!!!
« Reply #2 on: November 14, 2018, 06:20:32 AM »

Very nice. I have thought about getting a HF welder and teaching myself by messing up my Jeep. This inspires me a little. Wink

Logged

Dain

1984 CJ-8 Scrambler
3.5" lift
DD and trail toy

1949 CJ 3a - Stock - Garage queen

2015 JKU - Completely stock - Family mobile
AngryEchoSix
Offline
Forum User
Posts: 80
Busted Knuckle Garage Expert
« Reply #3 on: November 18, 2018, 12:28:13 PM »

Very nice. I have thought about getting a HF welder and teaching myself by messing up my Jeep. This inspires me a little. Wink

That's what I did, caught a HF Mig welder on sale and next thing I knew I was fabbing up a set of flat fenders for the front of my old TJ. Blue Torch Fab makes a nice kit for the TJ.

Logged

2014 JK Unlimited Rubicon X
Pages: [1] Go Up
  Print  
 
Jump to:  

Powered by EzPortal
Officers:
President: Stephen Clough (overhead) | Vice President: Donnie Herrity (Jeepin_Donnie) | Secretary: Robyn Kronthal (sticksout)
 Treasurer: Danille Wilson (TJ Girl) | Member-at-large: John Davis (jdavis2nd)

Board of Directors:
Andrew Harvin (HarvinJeep) | Dave Plummer (HAWAIICJ) | Sean McCready (Unl1mtd)
Jeff Wilson (jwilson2598) | Aaron Thomson (Jeep Freak) | Dain Wilson (Gr8Dain)

Founding Fathers:
 Jason Markvart (LNDSRK)  | Steve Scott (Islander90) | Josh Storer (Jastor)| Mike Finelli (BiggMike) | John Harper (Opie)

Disclaimer Statement:
All images from NoVaJeepers.net are exclusive to the Northern Virginia
Jeepers Association. Any reproduction of exclusive Northern Virginia
Jeepers Association material is strictly prohibited without written
consent of the Northern Virginia Jeepers Association. Jeep,
Wrangler, Cherokee, Commander, Compass, Patriot, Liberty, Unlimited,
Rubicon, SRT, HEMI and Grand Cherokee are copyrighted and trademarked
to Chrysler LLC. NoVaJeepers.com, Northern Virginia Jeepers Association
is not in any way associated with the Chrysler LLC.
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines | Theme Design by: Xarcell